ROM Features – These are the features our dealers can setup for you on a NepTune chip without any extra hardware. A small license fee is required to be tuned on NepTune. | |
*Fuel/Ignition Maps | |
Primary and Secondary Maps | Primary and Secondary low and high cam fuel and ignition maps. 8 maps total. 24 load breakpoints by 24 rpm breakpoints for precise tuning. Low and high cam both can be scaled to go to 11000 and above |
*Rev Limits/VTEC | |
Rev Limits Per Gear | |
Fuel And/Or Ignition Cut | |
High and Low Cam Rev Limits | Low cam rev limit doubles as a cold limit |
High and Low Load VTEC Engagement RPMs | Separate engagement RPMs for low and high load |
TPS threshold decides low/high load | This option decides whether to use the low or high load engagement RPM |
Minimum load for engagement | This option only allows VTEC to engage above the specified load |
Disengage below minimum load | When VTEC is engaged this option determines whether or not to disengage below the minimum load or disengage below the set engagement RPM |
Minimum Speed | |
Minimum ECT | |
VTEC Disable | For Non-VTEC setups |
VTEC Speed Threshold Disable | Allows VTEC to activate at launch or on setups without a VSS |
VTEC Temperature Threshold Disable | Allows VTEC to activate while the car isn't fully warmed up |
VTEC Pressure Disable | For setups without a VTEC Pressure switch |
VTEC Error Check Disable | Only suggested for race vehicles |
*Corrections | |
New and old injector size | Can be used with the overall trim to rescale for new injector sizes |
Overall Fuel Trim | Globally applied fuel correction |
TPS Tip-In Fuel Trim | Correction to accurately tune TPS Tip-In for different size injectors and different setups |
Cranking Fuel Trim | Fuel correction for Raw Cranking Fuel Maps |
Post Start Fuel Trim | Correction for fuel delivered immediately after startup |
Adjustable ECT vs Raw Cranking Fuel Maps | Used to determine how much fuel is used to start the engine |
Adjustable ECT vs Fuel Enrichment Maps | Used for cold start enrichment |
Adjustable ECT vs Ignition Correction Maps | Used for cold start correction |
Adjustable IAT vs Fuel Enrichment Maps | Complete fuel correction for weather changes |
Adjustable IAT vs Ignition Correction Maps | Ignition correction for intake temperature |
Adjustable Gear Based Fuel Enrichment Maps | Allows balancing of air/fuel ratios between different gears |
Adjustable Gear Based Ignition Correction Maps | Can be used as an aid for traction |
Adjustable Idle Ignition Corrections | |
Adjustable Ignition Limitations For Ignition Maps | |
Adjustable Ignition Dwell Control | |
Adjustable Tip-In Ignition Corrections | |
Adjustable Individual Cylinder Fuel Trim | Allows adjustments to fuel to obtain equal individual cylinder EGTs and more |
Injector Battery Compensation | Allows adjustments to fuel based on battery voltage |
*Idle | |
Target Idle | |
ECT vs Target Idle maps | Fully adjustable ECT and target idle values for the startup idle maps |
IACV Duty Cycle Adjustment | Allows adjustment of IACV duty cycle to help you reach your target RPM |
*AC Cutoff | |
Above RPM | |
Above TPS threshold | |
Idle Recovery | Disengages the AC clutch below this RPM to help regain control over a low idle |
*3-step | |
Activation by MPH | No need for a clutch switch! |
Activation by TPS threshold | Rev until any RPM you choose, cross the TPS threshold and it holds that RPM |
Activation by switch/clutch switch | Can be used to turn 2-step on/off or used as a clutch input |
MPH threshold for 2-step | Can help limit you off the line to keep traction under control |
Ignition Retard/Fuel Enrichment | Allows you to build boost off the 2-step |
TPS threshold for retard/enrichment | Allows you to pre-stage on the 2-step before building boost |
Full Throttle Shift | Holds the target RPM during shifts. Requires use of a clutch input |
Selectable clutch switch input | Several inputs to choose from to fit what's available |
*Outputs (2) | |
Activation Input | Not required for activation but can be used as an on/off switch |
Activation Output | Several outputs to choose from |
Minimum RPM | |
Maximum RPM | |
Minimum Load | |
Maximum Load | |
Minimum speed | |
Minimum Throttle Position | |
Minimum Intake Air Temperature | |
Maximum Intake Air Temperature | |
Minimum Engine Coolant Temperature | |
Maximum Engine Coolant Temperature | |
Ignition Retard By RPM | Retards ignition while activated |
Fuel Enrichment By RPM | Adds fuel while activated |
Switch maps on activation | Ability to use secondary maps to completely tune for nitrous |
Disable on FTL/FTS | |
Disable if MIL code | |
*Boost Control | For use with dual, tri, and quad stage boost controllers |
Activation Input | Not required for activation but can be used as an on/off switch |
Activation Output | Selectable outputs for each stage of boost |
Minimum RPM | |
Minimum speed | |
Minimum Throttle Position | |
Boost Cut | Keeps you from going over a determined safe level of boost |
PWM Based Boost Control | |
Variable Frequency For Multiple Solenoid Types | |
Quick Spool Duty Cycle And Load Setting | Allows you to hold a specific duty cycle until the load condition |
Set Duty | |
Boost By Gear | |
Boost By Gear vs RPM | |
Low/Hi Boost Switch Input | |
*Fan Control | Allows full control of what temperature the fan is activated |
Activation Output | |
Minimum Engine Coolant Temperature | |
Maximum Speed | |
*Switch Maps | |
Flexible Dual Map Setup | Primary and secondary maps can be setup to use MAP or TPS as load reference, Load and RPM breakpoints can be completely different. Can be used for extending load points/rpm breakpoints, alpha-n scaling, pump/race tunes, etc |
Activation Input | Not required for activation but can be used as a switch between the different maps |
Minimum RPM | |
Minimum Load | Optional setting, can be disabled. For use with maps extending onto the secondary maps |
Minimum Throttle Position | Optional setting, can be disabled. For use with Alpha-N scaling for ITB tuning |
Use High Cam Maps Only | Can be used to tune VTEC setups using one set of maps only |
*Anti-Theft | |
Required Inputs | Can require multiple inputs to be set or unset |
Optionally Required Code | Code is entered via presses of the TPS and Brake Pedal |
Valet/Fallback Mode | Allows vehicle to start with adjustable rev limit as valet or fallback for Anti-Theft |
*Closed Loop Control | |
Full Wideband Support | Works with full 0-5v scale |
Target O2 Voltage | Can be changed to set target closed loop a/f |
Disable Closed Loop Above Load | Beneficial to small turbo and supercharged setups that build boost even at partial throttle |
Other Conditions | Conditions for ECT, IAT, and RPM |
Adjustable Voltage Error | Disables closed loop in the event of sensor failure |
Disable Closed Loop Error Option | |
*Sensors and more | |
Disable Knock Sensor | |
Disable Injector Test Circuitry | Many EDM/JDM ECUs do not have this |
Disable BARO Sensor | Many EDM/JDM ECUs do not have this |
Disable ELD | |
Disable O2 Heater | Allows use of 1 wire O2 sensor or no O2 sensor if Closed Loop is disabled |
Disable IACV Error | For vehicles that don't have an IACV hooked up |
Disable IAB | |
IAB Activation RPM | |
MAP Sensor Support | Support for a wide range of map sensors from stock up to 5 bar and beyond via custom map settings |
Sensor Adjustments | Allows fuel, ignition, and PWM duty cycle to be altered based on a 0-5v analog input |
4 Programmable Analog Inputs | Allows logging of any 0-5v sensor. Breakpoints are fully configurable. |
*Extras | |
Service Input | Allows you to change the service input to any other input or none at all. This frees up the service connector to be used as a switch for one of the other options. Codes are also shown with the car off key in the on position with the throttle over 65% |
Clear Codes With The Brake Pedal | If you wish to clear codes in memory you can press the brake pedal while checking your codes to clear them from memory |
Adjustable Fuel Prime Time | |
MIL Shiftlight Per Gear | Activates the MIL at the specified RPM |
Adjustable Deceleration Fuel Cut | Load, Speed, and TPS dependent |
Lock Ignition Timing | Lock ignition steady to set ignition timing |
Injector Kill | To kill the engine without keying off |
Neptune Rtp Keygen Key
Neptune Rtp
- Neptune XT™ High Resolution Multicollector ICP-MS: First with 10 13 Ω Amplifier Technology, extending the benefits of Faraday cup detectors to smaller sample amounts. Now available with gain calibration and tau correction. First for sensitivity – the Jet Interface offers the highest ICP-MS sensitivity available.
- RTP 2000 HC is designed to provide the critical impact resistance and comparable shrink rate and moldability of amorphous polymers (e.g., PC and PC/ABS alloys), but can withstand the chemical attack by the aggressive cleaners and disinfectants used to control the spread of infections in hospitals.
- Hondata S300 Custom Remote E-tune Neptune Rtp Honda Kpro Flash Pro. 299.99. .. 2x Hondata Decals Stickers Vinyl Jdm Tuning Ecu Performance Import Japanese. 12.64.
- And if the stock ecu if capabile of handling the tuning needs of honda why wouldn't it be enough to handle the tuning needs of a modied motor. That's why I think that the s-300 and RTP are more than adequate. As far as the best choice of those two, I will say i went with the s-300 because i couldn't wait for the neptune rtp.
- And if the stock ecu if capabile of handling the tuning needs of honda why wouldn't it be enough to handle the tuning needs of a modied motor. That's why I think that the s-300 and RTP are more than adequate. As far as the best choice of those two, I will say i went with the s-300 because i couldn't wait for the neptune rtp.
- The app supports the following protocols: - Crome QD2 (Honda™) - Crome QD2 with Moates Demon (Honda™) - Crome QD3 (Honda™) - eCtune (Honda™) - ECUMaster EMU - KTuner R1 (Honda™) - KTunerFlashV1.2 (Honda™) - KTunerFlashV2 (Honda™) - Neptune (Honda™) - Neptune RTP (Honda™) - GUFB with Moates QuarterHorse (Ford™) - CBAZA with ..
- Find any PDF's or templates for any Fender lap steels online. Nov 25, 2015 - This lap steel was made from an extra 2x4 I ha. Then use a contractor's square to draw the fret lines. I went to Seymour Duncan's wiring guide page and got the PDF diagram for a humbucker pickup and one volume knob. Find great deals on eBay for lap steel fret board.
- 23.4k Followers, 788 Following, 3,487 Posts - See Instagram photos and videos from Xenocron Tuning Solutions (@xenocrontuning)
- Combined with datalogging RTP becomes an even more useful tool which enables auto-tuning. With the right setup, it is possible plugin an RTP enabled ECU, connect it to Crome, and with a wideband O2 sensor and datalogging support, be able to drive around the block and let the software make all the tuning changes.
- Neptune rtp crack or license? joeynapp Location Offline Junior Member Reputation: 114. Thanks Given: 102 Thanks Received: 155 (8 Posts) Posts: 37 Threads: 4
- Jun 16, 2015 · Use the native RTP encoder's software or interface to generate a Session Description Protocol (.sdp) file that describes the stream. For help, see the encoder's documentation. Name the file myStream.sdp and copy it to the [ install-dir ]/content folder on the server that runs Wowza Streaming Engine.
Neptune Rtp Software
Neptune Rtp Download
ROM Features – These are the features our dealers can setup for you on a NepTune chip without any extra hardware. A small license fee is required to be tuned on NepTune. | |
*Fuel/Ignition Maps | |
Primary and Secondary Maps | Primary and Secondary low and high cam fuel and ignition maps. 8 maps total. 24 load breakpoints by 24 rpm breakpoints for precise tuning. Low and high cam both can be scaled to go to 11000 and above |
*Rev Limits/VTEC | |
Rev Limits Per Gear | |
Fuel And/Or Ignition Cut | |
High and Low Cam Rev Limits | Low cam rev limit doubles as a cold limit |
High and Low Load VTEC Engagement RPMs | Separate engagement RPMs for low and high load |
TPS threshold decides low/high load | This option decides whether to use the low or high load engagement RPM |
Minimum load for engagement | This option only allows VTEC to engage above the specified load |
Disengage below minimum load | When VTEC is engaged this option determines whether or not to disengage below the minimum load or disengage below the set engagement RPM |
Minimum Speed | |
Minimum ECT | |
VTEC Disable | For Non-VTEC setups |
VTEC Speed Threshold Disable | Allows VTEC to activate at launch or on setups without a VSS |
VTEC Temperature Threshold Disable | Allows VTEC to activate while the car isn't fully warmed up |
VTEC Pressure Disable | For setups without a VTEC Pressure switch |
VTEC Error Check Disable | Only suggested for race vehicles |
*Corrections | |
New and old injector size | Can be used with the overall trim to rescale for new injector sizes |
Overall Fuel Trim | Globally applied fuel correction |
TPS Tip-In Fuel Trim | Correction to accurately tune TPS Tip-In for different size injectors and different setups |
Cranking Fuel Trim | Fuel correction for Raw Cranking Fuel Maps |
Post Start Fuel Trim | Correction for fuel delivered immediately after startup |
Adjustable ECT vs Raw Cranking Fuel Maps | Used to determine how much fuel is used to start the engine |
Adjustable ECT vs Fuel Enrichment Maps | Used for cold start enrichment |
Adjustable ECT vs Ignition Correction Maps | Used for cold start correction |
Adjustable IAT vs Fuel Enrichment Maps | Complete fuel correction for weather changes |
Adjustable IAT vs Ignition Correction Maps | Ignition correction for intake temperature |
Adjustable Gear Based Fuel Enrichment Maps | Allows balancing of air/fuel ratios between different gears |
Adjustable Gear Based Ignition Correction Maps | Can be used as an aid for traction |
Adjustable Idle Ignition Corrections | |
Adjustable Ignition Limitations For Ignition Maps | |
Adjustable Ignition Dwell Control | |
Adjustable Tip-In Ignition Corrections | |
Adjustable Individual Cylinder Fuel Trim | Allows adjustments to fuel to obtain equal individual cylinder EGTs and more |
Injector Battery Compensation | Allows adjustments to fuel based on battery voltage |
*Idle | |
Target Idle | |
ECT vs Target Idle maps | Fully adjustable ECT and target idle values for the startup idle maps |
IACV Duty Cycle Adjustment | Allows adjustment of IACV duty cycle to help you reach your target RPM |
*AC Cutoff | |
Above RPM | |
Above TPS threshold | |
Idle Recovery | Disengages the AC clutch below this RPM to help regain control over a low idle |
*3-step | |
Activation by MPH | No need for a clutch switch! |
Activation by TPS threshold | Rev until any RPM you choose, cross the TPS threshold and it holds that RPM |
Activation by switch/clutch switch | Can be used to turn 2-step on/off or used as a clutch input |
MPH threshold for 2-step | Can help limit you off the line to keep traction under control |
Ignition Retard/Fuel Enrichment | Allows you to build boost off the 2-step |
TPS threshold for retard/enrichment | Allows you to pre-stage on the 2-step before building boost |
Full Throttle Shift | Holds the target RPM during shifts. Requires use of a clutch input |
Selectable clutch switch input | Several inputs to choose from to fit what's available |
*Outputs (2) | |
Activation Input | Not required for activation but can be used as an on/off switch |
Activation Output | Several outputs to choose from |
Minimum RPM | |
Maximum RPM | |
Minimum Load | |
Maximum Load | |
Minimum speed | |
Minimum Throttle Position | |
Minimum Intake Air Temperature | |
Maximum Intake Air Temperature | |
Minimum Engine Coolant Temperature | |
Maximum Engine Coolant Temperature | |
Ignition Retard By RPM | Retards ignition while activated |
Fuel Enrichment By RPM | Adds fuel while activated |
Switch maps on activation | Ability to use secondary maps to completely tune for nitrous |
Disable on FTL/FTS | |
Disable if MIL code | |
*Boost Control | For use with dual, tri, and quad stage boost controllers |
Activation Input | Not required for activation but can be used as an on/off switch |
Activation Output | Selectable outputs for each stage of boost |
Minimum RPM | |
Minimum speed | |
Minimum Throttle Position | |
Boost Cut | Keeps you from going over a determined safe level of boost |
PWM Based Boost Control | |
Variable Frequency For Multiple Solenoid Types | |
Quick Spool Duty Cycle And Load Setting | Allows you to hold a specific duty cycle until the load condition |
Set Duty | |
Boost By Gear | |
Boost By Gear vs RPM | |
Low/Hi Boost Switch Input | |
*Fan Control | Allows full control of what temperature the fan is activated |
Activation Output | |
Minimum Engine Coolant Temperature | |
Maximum Speed | |
*Switch Maps | |
Flexible Dual Map Setup | Primary and secondary maps can be setup to use MAP or TPS as load reference, Load and RPM breakpoints can be completely different. Can be used for extending load points/rpm breakpoints, alpha-n scaling, pump/race tunes, etc |
Activation Input | Not required for activation but can be used as a switch between the different maps |
Minimum RPM | |
Minimum Load | Optional setting, can be disabled. For use with maps extending onto the secondary maps |
Minimum Throttle Position | Optional setting, can be disabled. For use with Alpha-N scaling for ITB tuning |
Use High Cam Maps Only | Can be used to tune VTEC setups using one set of maps only |
*Anti-Theft | |
Required Inputs | Can require multiple inputs to be set or unset |
Optionally Required Code | Code is entered via presses of the TPS and Brake Pedal |
Valet/Fallback Mode | Allows vehicle to start with adjustable rev limit as valet or fallback for Anti-Theft |
*Closed Loop Control | |
Full Wideband Support | Works with full 0-5v scale |
Target O2 Voltage | Can be changed to set target closed loop a/f |
Disable Closed Loop Above Load | Beneficial to small turbo and supercharged setups that build boost even at partial throttle |
Other Conditions | Conditions for ECT, IAT, and RPM |
Adjustable Voltage Error | Disables closed loop in the event of sensor failure |
Disable Closed Loop Error Option | |
*Sensors and more | |
Disable Knock Sensor | |
Disable Injector Test Circuitry | Many EDM/JDM ECUs do not have this |
Disable BARO Sensor | Many EDM/JDM ECUs do not have this |
Disable ELD | |
Disable O2 Heater | Allows use of 1 wire O2 sensor or no O2 sensor if Closed Loop is disabled |
Disable IACV Error | For vehicles that don't have an IACV hooked up |
Disable IAB | |
IAB Activation RPM | |
MAP Sensor Support | Support for a wide range of map sensors from stock up to 5 bar and beyond via custom map settings |
Sensor Adjustments | Allows fuel, ignition, and PWM duty cycle to be altered based on a 0-5v analog input |
4 Programmable Analog Inputs | Allows logging of any 0-5v sensor. Breakpoints are fully configurable. |
*Extras | |
Service Input | Allows you to change the service input to any other input or none at all. This frees up the service connector to be used as a switch for one of the other options. Codes are also shown with the car off key in the on position with the throttle over 65% |
Clear Codes With The Brake Pedal | If you wish to clear codes in memory you can press the brake pedal while checking your codes to clear them from memory |
Adjustable Fuel Prime Time | |
MIL Shiftlight Per Gear | Activates the MIL at the specified RPM |
Adjustable Deceleration Fuel Cut | Load, Speed, and TPS dependent |
Lock Ignition Timing | Lock ignition steady to set ignition timing |
Injector Kill | To kill the engine without keying off |
Neptune Rtp Keygen Key
Neptune Rtp
- Neptune XT™ High Resolution Multicollector ICP-MS: First with 10 13 Ω Amplifier Technology, extending the benefits of Faraday cup detectors to smaller sample amounts. Now available with gain calibration and tau correction. First for sensitivity – the Jet Interface offers the highest ICP-MS sensitivity available.
- RTP 2000 HC is designed to provide the critical impact resistance and comparable shrink rate and moldability of amorphous polymers (e.g., PC and PC/ABS alloys), but can withstand the chemical attack by the aggressive cleaners and disinfectants used to control the spread of infections in hospitals.
- Hondata S300 Custom Remote E-tune Neptune Rtp Honda Kpro Flash Pro. 299.99. .. 2x Hondata Decals Stickers Vinyl Jdm Tuning Ecu Performance Import Japanese. 12.64.
- And if the stock ecu if capabile of handling the tuning needs of honda why wouldn't it be enough to handle the tuning needs of a modied motor. That's why I think that the s-300 and RTP are more than adequate. As far as the best choice of those two, I will say i went with the s-300 because i couldn't wait for the neptune rtp.
- And if the stock ecu if capabile of handling the tuning needs of honda why wouldn't it be enough to handle the tuning needs of a modied motor. That's why I think that the s-300 and RTP are more than adequate. As far as the best choice of those two, I will say i went with the s-300 because i couldn't wait for the neptune rtp.
- The app supports the following protocols: - Crome QD2 (Honda™) - Crome QD2 with Moates Demon (Honda™) - Crome QD3 (Honda™) - eCtune (Honda™) - ECUMaster EMU - KTuner R1 (Honda™) - KTunerFlashV1.2 (Honda™) - KTunerFlashV2 (Honda™) - Neptune (Honda™) - Neptune RTP (Honda™) - GUFB with Moates QuarterHorse (Ford™) - CBAZA with ..
- Find any PDF's or templates for any Fender lap steels online. Nov 25, 2015 - This lap steel was made from an extra 2x4 I ha. Then use a contractor's square to draw the fret lines. I went to Seymour Duncan's wiring guide page and got the PDF diagram for a humbucker pickup and one volume knob. Find great deals on eBay for lap steel fret board.
- 23.4k Followers, 788 Following, 3,487 Posts - See Instagram photos and videos from Xenocron Tuning Solutions (@xenocrontuning)
- Combined with datalogging RTP becomes an even more useful tool which enables auto-tuning. With the right setup, it is possible plugin an RTP enabled ECU, connect it to Crome, and with a wideband O2 sensor and datalogging support, be able to drive around the block and let the software make all the tuning changes.
- Neptune rtp crack or license? joeynapp Location Offline Junior Member Reputation: 114. Thanks Given: 102 Thanks Received: 155 (8 Posts) Posts: 37 Threads: 4
- Jun 16, 2015 · Use the native RTP encoder's software or interface to generate a Session Description Protocol (.sdp) file that describes the stream. For help, see the encoder's documentation. Name the file myStream.sdp and copy it to the [ install-dir ]/content folder on the server that runs Wowza Streaming Engine.
Neptune Rtp Software
Neptune Rtp Download
Neptune Rtp Keygen Free Keygenguru Serial Key Pdf Xchange Viewer Gururajulu Naidu Harikathe Rar Max Payne 2 Free Download For Android Pipesim Software Crack. 1/13/2019 1 Comment Significant new functionality and enhanced integration, from exploration to production. The latest release of the Petrel E&P software platform introduces a new user. Neptune Rtp Keygen Baixar Novela Marimar Dublado Completa Lagu Malaysia Uks Cinta Itu Buta Endnote X7 Serial Number Raam Kannada Movie Songs Free Download 123musiq Aim Hack Cs Source Torrent Ek Duje Ke Liye Old Movie mp3 songs free, download Download R. Neptune Rtp Keygen YAMATA GK26-1A Portable Bag Closer Heavy Duty Industrial Sewing Machine 220V!!! Excel for mac create relationship between tables. From United States. Was: Previous Price $210.00 +$107.65 shipping. Gemsy Jiasew 4' Cutting Blade Stand Up Electric Rotary Knife Cutter. From United States.
Download the latest drivers, firmware, and software for your HP LaserJet 1018 Printer.This is HP's official website that will help automatically detect and download the correct drivers free of cost for your HP Computing and Printing products for Windows and Mac operating system. Mac Driver (for High Sierra also) for HP LaserJet 1018 (1020, 1022, etc?) 08:55 AM. Product: LaserJet 1018. To install the HP 1018 printer with High Sierra I downloaded the file 'HewletPackardPrinterDrivers5.1.dmg' from the Apple website (here: https. Select the listed Laserjet 1018. Click the Use drop-down and click Select printer software. Select the Laserjet 1022 from the list, add the printer and try printing using the configured printer. If that does not help you may also try the 3rd party foo2zjs drivers. Connect the USB cable to the USB port on the Mac and to the printer. Download and install the HP Printer Drivers v5.1 for OS X. On the Apple menu, click System. Thanx brother ur answer was really helpful only one thing i need to add for HP LaserJet 1018 owners that in the given drivers package there are no drivers for HP LJ1018 but 1022. Ensure the printer is powered on and the USB is directly connected to your Mac. Click the Apple icon, select System Preferences and then go to Printers & Scanners. Click the plus sign and select the listed 1018 printer. Click the Use drop-down menu and then click on Select Printer Software. Hp 1018 driver for mac.